Search:

Type: Posts; User: jwells

Page 1 of 20 1 2 3 4

Search: Search took 0.03 seconds.

  1. Replies
    23
    Views
    55,891

    Power wheelies-no problem!

    Power wheelies-no problem!
  2. Interesting, thanks for the insight, always...

    Interesting, thanks for the insight, always impressive!
  3. Replies
    23
    Views
    55,891

    Absolutely amazing! 128K on the clock, testament...

    Absolutely amazing! 128K on the clock, testament to the bike and your maintenance! Good job.
  4. Thread: Break in period

    by jwells
    Replies
    1
    Views
    495

    Do it, still follow the mfg's break in. ...

    Do it, still follow the mfg's break in.

    Bigger question, how do you have an '08 with no miles on it!?

    Thanks for your support.
  5. Replies
    5
    Views
    1,406

    Hey, sorry for the late response-been on the road...

    Hey, sorry for the late response-been on the road at Sturgis Rally the last few weeks.

    FatShots are a lower/deeper tone than the SE. The larger diameter muffler with more internal volume is the...
  6. Replies
    5
    Views
    1,406

    Our FatShots are great, deep low tone,...

    Our FatShots are great, deep low tone, adjustable.

    Kerker Stouts are a good option as well, little louder non adjustable
    SuperTrapp Stouts are on the quiet side.
  7. Replies
    5
    Views
    1,406

    On your bike they will be pretty loud and...

    On your bike they will be pretty loud and metallic. Not good. As you know they have a solid core with not packing. You could buy the 'Performance Core' kits for them but that would probably negate...
  8. Replies
    4
    Views
    941

    That is close, motor ever been out?

    That is close, motor ever been out?
  9. Replies
    4
    Views
    941

    With age, check all rubber mounts they tend to...

    With age, check all rubber mounts they tend to wear and get sloppy.
    Glad you like the pipe, thank you!
  10. Replies
    1
    Views
    1,075

    The shallow back calipers are made for exactly...

    The shallow back calipers are made for exactly your application, 21" spoke. The caliper mount face to center line for rotor would be .625" There are no drawings on line-sorry.
  11. Replies
    1
    Views
    719

    That was for a Thunder Mountain Spitfire, a...

    That was for a Thunder Mountain Spitfire, a sportster motor with a right side drive.
    The pipe would physically fit your motor, but because it was made for the right side drive wide tire it will...
  12. Replies
    13
    Views
    9,088

    The badge is p/n; 8009, they are 20.30. We can...

    The badge is p/n; 8009, they are 20.30. We can put one in the mail USPS to you for 5.00 extra. There is no way to track this however. Or we can FedEx, but last time I looked this up it's 30+?
    If you...
  13. Replies
    1
    Views
    821

    http://supertrapp.com/images/pdfs/003-7088.pdf...

    http://supertrapp.com/images/pdfs/003-7088.pdf
    Step 1 in the instructions notes the 'dent' in the muffler. It is for proper clearance near the cross over tube.
    Thanks.
  14. Replies
    1
    Views
    1,267

    Thank you! Your English is perfect also. Your...

    Thank you!
    Your English is perfect also.

    Your bike sounds fun, you could try adding a few (20-21) but the bigger question is how is it running now? If it's pulling off the bottom well, and clean...
  15. Replies
    1
    Views
    812

    Sorry, missed this post earlier. On the later...

    Sorry, missed this post earlier. On the later model bike, the Stout mufflers are THE way to go. They are larger body, deeper mellow tone. They come with end cap ready to go. Where the other smaller...
  16. Replies
    3
    Views
    1,091

    Awesome! I usually put the sensors in first...

    Awesome! I usually put the sensors in first before installing pipe and then run the wires back up.
    Looks good David!
  17. Replies
    9
    Views
    4,182

    David, sounds like a fun set up! Also sounds...

    David, sounds like a fun set up!
    Also sounds like your tuner is familiar and probably has some thoughts on this as well, but probably just start right with the 20 and closed cap. Might want to get...
  18. Replies
    3
    Views
    1,091

    David, the Heritage is a little different than...

    David, the Heritage is a little different than the other models.
    The other bikes have bolts that hold the bracket.
    The key is to just be sure that everything lines up smoothly and nothing is...
  19. Replies
    3
    Views
    1,138

    304-3034 is the part number. Thank you.

    304-3034 is the part number. Thank you.
  20. Replies
    3
    Views
    1,138

    I would recommend getting a couple open end caps...

    I would recommend getting a couple open end caps and using the open end cap along with about 6-8 discs. The open end cap allows the heat to escape better inside the mufflers.

    Thanks,
  21. Replies
    3
    Views
    1,096

    100-7157 is the part number, that is core/end...

    100-7157 is the part number, that is core/end cap/packing ready to slide in (uses 1/4-20x.5 screws/lock washers)
    This is 102.00.
    You can give a call to Customer Service to place an order....
  22. Replies
    3
    Views
    1,096

    Everything we make will have some sort of part...

    Everything we make will have some sort of part number on it. Muffler will be stamped at either the inlet of the muffler where it slides on or the bracket. Take a look, get that number and we can...
  23. Thread: FatShot 2:1

    by jwells
    Replies
    1
    Views
    1,585

    FatShot 2:1

    https://www.youtube.com/watch?v=Gi5CIDJfack
  24. Thread: Bootlegger

    by jwells
    Replies
    0
    Views
    848

    Bootlegger

    https://www.youtube.com/watch?v=VrTANGP-0YA
  25. Thread: Bootlegger!

    by jwells
    Replies
    0
    Views
    669

    Bootlegger!

    Our New Bootlegger Stainless 2:1; stepped headpipes, adjustable end caps (optional caps available) $859 retail!223224225
Results 1 to 25 of 500
Page 1 of 20 1 2 3 4