PDA

View Full Version : Supertrapp for old generation Confederates



reesmicm
06-28-2014, 04:02 AM
Which Supertrapp universal system was used on the Confederates (GT and Hellcat). Purchasing a used Confederate and they have a Muzzy system put on, but I perfer the Supertrapp system that was put on before switching to Muzzy. My Confederate is a GT with a 131 inch Merch motor.
thanks.

bschultz
07-01-2014, 07:20 AM
The 2:1 system we produced for Confederate (P/N 829-10000) was discontinued in '02. Components to the system have been exhausted for several years.

reesmicm
07-01-2014, 09:51 PM
The 2:1 system we produced for Confederate (P/N 829-10000) was discontinued in '02. Components to the system have been exhausted for several years.

Bob,
I have the header, would you still have the megaphone slipon that would be close? Just want to get rid of that Muzzy slipon.
Mike

bschultz
07-02-2014, 07:16 AM
The 4" Aluminum Racing Series Universal, P/N 422-2500 + 6 pack of discs, P/N 404-6506.

reesmicm
07-06-2014, 12:30 AM
just to double check, my header is 2 1/4" at the slipon.

bschultz
07-07-2014, 07:23 AM
According to the bill of materials for the system WE made for it...should be a 2.5" AND the Universal recommended should be an exact replacement.
If you need something with a 2.25" inlet, look at the S/C Series Universal.

reesmicm
07-27-2014, 09:01 PM
Bob,
Found a complete ST Confederate system from a friend. Need a mounting clamp, looks like a P-Clamp that is around 3" from mid-point of pipe and the mounting point bolt. Did you supply these for the Confederate pipes? If not would you have anything that would be close. Dying to get this Muzzy system off the of bike.
thanks again.
Mike

bschultz
07-30-2014, 07:13 AM
We did supply a 2:1 pipe for the to Confederate; however a check of the BOM & hardware kit does NOT indicate we supplied a "P" clamp.

reesmicm
07-30-2014, 08:47 AM
Bob,

Appreciate it.

The P-Clamp is a guess. Do you know if any type of mounting bracket was supplied by Supertrapp as we usually get with normal OEM systems like my Wide Glide?

Would you have any mounting P-clamp type brackets from other installations that might work with this 2 1/2" header? It's aroudn 3" from mid point on pipe ot mounting stud. I can cut down a clamp if it's longer.

thanks


We did supply a 2:1 pipe for the to Confederate; however a check of the BOM & hardware kit does NOT indicate we supplied a "P" clamp.

bschultz
07-31-2014, 12:15 PM
Bob,

Appreciate it.

The P-Clamp is a guess. Do you know if any type of mounting bracket was supplied by Supertrapp as we usually get with normal OEM systems like my Wide Glide?

Would you have any mounting P-clamp type brackets from other installations that might work with this 2 1/2" header? It's aroudn 3" from mid point on pipe ot mounting stud. I can cut down a clamp if it's longer.

thanks

As with many of the OEM pipes we supply there was NONE in the BOM (Manufacturer/builder supplied their own). We do have P-clamps and brackets for many applications; however finding one that might work would be a shot in the dark.

reesmicm
08-12-2014, 10:17 AM
As with many of the OEM pipes we supply there was NONE in the BOM (Manufacturer/builder supplied their own). We do have P-clamps and brackets for many applications; however finding one that might work would be a shot in the dark.

Bob,
Can you recommend a clamp part number for the pipe and I can make the flat bracket that goes to the mounting point. Just need P-clamp that is able to connect to a bracket.
Mike

bschultz
08-13-2014, 07:01 AM
Contact our Customer Service Department.