PDA

View Full Version : Yamaha V-star 1100 exhaust



fulltilt1
08-11-2007, 05:49 PM
Just bought a V-star 1100. I didn't see a direct application, will there be one in the future? My stock pipes had the baffles removed by the previous owner. They are approx 3" in diameter, is there a way to get a baffle for these pipes as a custom application?

hugger
08-13-2007, 08:43 AM
Just bought a V-star 1100. I didn't see a direct application, will there be one in the future? My stock pipes had the baffles removed by the previous owner. They are approx 3" in diameter, is there a way to get a baffle for these pipes as a custom application?

There are no plans to do anything for the V Stars.

We possibly can find a core to fit your pipes! I need to know more information!
And talking to you would be very helpful, please email me your daytime phone #. Thanks! Gerry

Please email me directly: hugger@supertrapp.com

fulltilt1
08-13-2007, 04:18 PM
the number is [phone number edited out by admin] Right now its parked at a friends garage I may get it tonight or tomorrow to ride this week. I will Mic the ID of the pipe then. If we can find something close, I have some machinist friends who can work wonders.

[ADMIN'S NOTE: It's not a good idea to post phone numbers in a public forum. In the future, email or the private message function of the forum is a much better choice. Thank you]

fulltilt1
08-13-2007, 04:19 PM
should have asked what dimensions will you need. The pipes are straight tube, no taper.

fulltilt1
08-14-2007, 07:26 PM
I mic'd the pipes the outlet is 3.46 to 3.48 in. ID and the head pipes are 1.4in OD. Hope we can make this work. I think they would look good.

hugger
08-23-2007, 01:26 PM
Right now its parked at a friends garage I may get it tonight or tomorrow to ride this week. I will Mic the ID of the pipe then. If we can find something close, I have some machinist friends who can work wonders.


I will need the inside diameter of the outlet of the muffler, the length of the muffler or length of core you can use and the outside diameter of the headpipe that the muffler slides onto.

hugger
08-23-2007, 01:36 PM
I mic'd the pipes the outlet is 3.46 to 3.48 in. ID and the head pipes are 1.4in OD. Hope we can make this work. I think they would look good.

Do you need muffler or just the cores to go inside? I only have one muffler option if you want mufflers too? Please go to this: link:http://www.supertrapp.com/product_sections/cat.asp?CatID=35

The cores that I have that might work are 3.39" outside diameter and are 20.7" long, they will use the 3"discs. If you are serious about doing this please email me directly so that I can communicate with you personally. I do not want to share your personal info ie:phone #. I will wait to hear from you since I know that I can help you solve your problem. My email: hugger@supertrapp.com

hugger
08-23-2007, 01:37 PM
should have asked what dimensions will you need. The pipes are straight tube, no taper.

I think I have you covered! Just need to know if you need mufflers or just cores to go into your existing mufflers!!

hugger
08-23-2007, 01:38 PM
I mic'd the pipes the outlet is 3.46 to 3.48 in. ID and the head pipes are 1.4in OD. Hope we can make this work. I think they would look good.

Please see earlier responses! Thanks!
Gerry

fulltilt1
09-01-2007, 12:50 PM
Sorry I was out of the country for work reasons. That link just took me to a page with part numbers, no descriptions no nothing.

bschultz
09-05-2007, 12:39 PM
Gerry asked me to advise you that we do not have a core assembly that will fit your muffler body. You may want to look at our Universal line of mufflers as a replacement. You would most likely need to fabricate a connector pipe and/or bracket.